CORRECT CRAFT Air Nautique Specifications download pdf (Page 8)

100

Programming the Primary User Code

Make sure that the system indicator light is off. Until a primary user code is

set, the keyless ignition will behave as follows. Pressing start once will unlock

the system while pressing it a second time will start the engine. Pressing stop

once will turn off the engine while pressing it a second time will lock the

system.

To program the primary user code, press buttons one and four at the same time,

putting the system in code programming mode. The system indicator light will

be flashing.

Enter a code from two to eight characters long and press start. For verification,

re-enter the code and press start again. The system indicator light should stop

flashing and stay on. If the light does not stop flashing, press stop and begin

again.

To lock the system re-enter either the primary user code or the master

embedded code and press stop.

Changing the Primary User Code

NOTE: The current primary code must be used to change to another primary

code.

Make sure that the system indicator light is off. Enter the primary user code

then press buttons one and four at the same time. This puts the system in code

programming mode. The system indicator light will be flashing.

Enter a code from two to eight characters long and press start. For verification,

re-enter the code and press start again. The system indicator light should stop

flashing and stay on. If the light does not stop flashing, press stop and begin

again.

To lock the system re-enter either the new primary user code or the master

embedded code and press stop. Please note, changing the primary code will

erase the secondary user code. The secondary code will need to be re-entered.

Programming or Changing the Secondary User Code

NOTE: The secondary code will only lock or unlock the system & can not be

used for any reprogramming

Make sure that the system indicator light is off. Enter the primary user code

and press buttons one and three at the same time putting the system in code

programming mode. The system indicator light will be flashing.

Enter a code from two to eight characters long and press start. Re-enter the

code and press start again. The system indicator light should stop flashing and

stay on. If the light does not stop flashing, press stop and begin again.

To lock the system re-enter any of the three codes and press stop.

1.4

Sport-Air2002.qxd 8/21/01 9:08 AM Page 1.4

Programming the Primary User Code

Make sure that the system indicator light is off. Until a primary user code is

set, the keyless ignition will behave as follows. Pressing start once will unlock

the system while pressing it a second time will start the engine. Pressing stop

once will turn off the engine while pressing it a second time will lock the

system.

To program the primary user code, press buttons one and four at the same time,

putting the system in code programming mode. The system indicator light will

be flashing.

Enter a code from two to eight characters long and press start. For verification,

re-enter the code and press start again. The system indicator light should stop

flashing and stay on. If the light does not stop flashing, press stop and begin

again.

To lock the system re-enter either the primary user code or the master

embedded code and press stop.

Changing the Primary User Code

NOTE: The current primary code must be used to change to another primary

code.

Make sure that the system indicator light is off. Enter the primary user code

then press buttons one and four at the same time. This puts the system in code

programming mode. The system indicator light will be flashing.

Enter a code from two to eight characters long and press start. For verification,

re-enter the code and press start again. The system indicator light should stop

flashing and stay on. If the light does not stop flashing, press stop and begin

again.

To lock the system re-enter either the new primary user code or the master

embedded code and press stop. Please note, changing the primary code will

erase the secondary user code. The secondary code will need to be re-entered.

Programming or Changing the Secondary User Code

NOTE: The secondary code will only lock or unlock the system & can not be

used for any reprogramming

Make sure that the system indicator light is off. Enter the primary user code

and press buttons one and three at the same time putting the system in code

programming mode. The system indicator light will be flashing.

Enter a code from two to eight characters long and press start. Re-enter the

code and press start again. The system indicator light should stop flashing and

stay on. If the light does not stop flashing, press stop and begin again.

To lock the system re-enter any of the three codes and press stop.

1.4

Sport-Air2002.qxd 8/21/01 9:08 AM Page 1.4

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 99 100

Comments to this Manuals

No comments

CORRECT CRAFT Air Nautique Specifications Page 8

Comments to this Manuals

Related products and manuals for Motor vehicle accessories & components CORRECT CRAFT Air Nautique